一臺電子皮帶秤的使用性能好壞，不僅取決于電子皮帶秤生產廠家的設計質量，而且還取決于現場的安裝工藝要求及設備的維護情況。

1、秤體安裝位置的選取

秤體應安裝在輸送機皮帶張力變化較小且安裝的部位不應有伸縮、接頭或縱梁拼接的地方，整個稱重域內托輥和輸送機的支撐應有足夠的強度和剛度，盡量避免風力、雨雪、暴曬、振動源、腐蝕性氣體、強磁場及大型機電設備的干擾，并且將安裝秤體的皮帶輸送機與振動料倉分離，避免振動信號對稱重信號的影響。

2、稱重托輥的選取及安裝

稱重托輥的徑向跳動，承重高度和槽行角的公差應在國家標準允許的范圍內，托輥的槽行角應在35°以下，槽型角偏大，勢必會引起托輥的不同心度，從而使皮帶的柔性變差。稱重域內托輥應比兩邊其它托輥高出6mm左右，且縱向中心線應與輸送機架掛輥中心線重合，而且與輸送機縱向平行。

3、電氣部分的安裝要求

電源部分應盡量避開動力線，亦可采用照明電源，有條件的用戶可在電腦積算器電源側增加電源穩壓裝置；電氣接線盒安裝于輸送機一側，應密封好，防止清掃輸送機架時，電路板被水浸泡或粉塵進入接線盒內；電腦積算器控制室和現場的距離較遠，可達幾百米，稱重信號線和電力電纜線應分開走線，且將屏蔽端接好，由于線路損耗較大、稱重信號受外界的干擾較嚴重，距離超過60米時，接線應采用6線制接法；電腦積算器和秤體應分別接地，接地電阻應不大于4Ω。

除以上基本要求以外，電子皮帶秤的安裝還應該做到針對性調試安裝，比如：需要專業的工程師根據現場環境判定最適合安裝皮帶秤的位置，準確找到與現場使用環境的契合度，電子皮帶秤生產廠家將為客戶提供上門安裝服務，安裝人員會以最豐富的技術經驗，確保客戶的皮帶秤在使用過程中精度和穩定，保證皮帶秤的穩定運行。